Disassembled Rudder to Start Deburring

March 1, 2010

Prev | Next

I liked having the rudder assembled on the workbench over the last day or so. I got to walk by it going in and out of the house admiring how much it looked like an airplane part. I found myself saying, “that’s a rudder” every time I walked by.

Nevertheless, the next step in the construction manual has you disassemble the parts and start the long process of prep for priming and riveting.

Some of the rudder parts, disassembled.

I got everything taken apart yesterday, and then second-guessed myself. I am planning on attaching most, if not all, of the fiberglass fairings with screws and nutplates, which will require the usual dimpling/countersinking of the components. Here’s the catch. Take the rudder bottom fairing attach strips. If I disassemble, deburr, scuff, clean, prime, and rivet them back to the skin/bottom rib, I’ll be drilling through primed parts when I go to install the bottom fairing (and nutplates). Do people re-prime these parts (mainly the holes) after they are riveted to the almost complete rudder?

I’m thinking that maybe I should re-assemble everything, layout the spacing for the fastener attach points now, then go ahead and do the normal disassemble, debur, scuff, clean, prime, and rivet dance. I’m going to pose this question on VAF.

Anyway, with everything disassembled, I started to mark and deburr parts. In preparation for edge finishing, I removed all of the safety covers for the scotchbrite wheel side of my 6″ grinder.

Removed the scotchbrite wheel.

Removed all safety covers.

Reattached scotchbrite wheel.

Ready for some edge-finishing.

Then, I got back to deburring some of the smaller parts. When I finished deburring the holes in a part, I usually take a scotchbrite pad and “mark” the part with a few scuffs. That way, I know all the holes are deburred, and it is time to move on to edge finishing.

I only spent an hour outside today. Had to let the food digest before working out, then it was off to bed.

[yawn] I’m still tired, though.

Prev | Next

Leave a Comment » | Empennage | Tagged: , , , , , , , , , | Permalink
Posted by Andrew

Stiffener Prep, Priming, and some Backriveting

February 25, 2010

Prev | Next

Tonight, I decided I wanted to get started on backriveting the stiffeners. First, I had to finish edge prepping them, and get them primed. Here are my edge prepping tools for these stiffeners.

Permagrit, scotchbrite, an edge deburring tool, and one of the stiffeners. Sorry about the dirty table, that's from me waxing my skis. See the big spot near the top of the picture. That's from me getting wax on the iron, and trying to scrape it off using the table. Maybe I'll turn my benchtop over tonight so I look like a clean builder again.

After getting a few of them prepped, I went ahead and started priming.

Stiffeners drying.

Here’s the right skin, ready to accept the stiffeners.

Right skin, with rivets ready to go.

At first, I tried this backriveting extra long double offset rivet set I got from Avery. I don’t really like this thing. With the pressure turned all the way up to 50 psig, the rivets weren’t really setting well, and the plastic sheath was marring the stiffeners.

Here's what I tried the for the first stiffener.

Although the results are good, I ended up switching to another set.

Very pretty. I'm sure some of that marring will come out during polish. Very nice surface, though.

Then I switched sets to a large7/16″ cupped set, which worked well to keep the set (with no plastic sheath) on the rivet as it was being driven, but left some of them with a little bit of a rounded edge. I’m sure this is okay, but need to have someone come look at it.

Still, they look pretty good.

Here’s a better shot. They are okay, but not perfect.

See the slight rounded edge to them? I'm sure that is okay.

I managed to get through 4 stiffeners before I started getting tired and went to bed.

4 of 8 stiffeners done on the right skin.

I pulled the tape off of the exterior side…these look really good. I am excited to maybe polish the rudder so you can all admire my work.

1 hour today, 50 rivets. Wuhoo!

Prev | Next

Leave a Comment » | Empennage | Tagged: , , , , , , | Permalink
Posted by Andrew

Vertical Stabilizer 99 Percent Complete

February 15, 2010

Prev | Next

Jack and Ginger were a little neglected this weekend while the girlfriend and I painted the master bedroom. I’m sorry, guys.

Anyway, tonight was all about them, so in the middle of playing, napping by the fire, and running in circles around the house, I managed to calm them down enough to help with the airplane a little.

With the few minutes I had, I managed to set the 22 rivets that were hard to reach with the squeezer last Friday night. A few of them, especially near the elevator hinge brackets, were still hard, but I managed to get them all set, even if it was after drilling a few out. I also set the three AN470AD4-6 rivets that hold the rear spar to the root rib and also install the three LP4-3 rivets that hold the rear spar to the middle rib.  Here are the dogs, once I got the vertical up into the ski equipment room, umm, I mean airplane parts storage room, umm, I mean burnt orange room.

The dogs flew again. This time with directional stability!

They aren’t really happy about being in the orange room in general (it is off limits, so they are very good about not crossing the threshold), but especially not when they have to pose in the airplane. I know for a fact, though, that they will love flying in it when it’s done.

Jack's not very happy about posing. He's ready to go.Jack's slightly less uncomfortable the further he is away from the "shiny blue thing that makes loud noises." Seriously, I heard him describe it that way.

Ginger’s okay, though. Especially when there is a bone on which she could be chewing.


Jack's slightly less uncomfortable the further he is away from the "shiny blue thing that makes loud noises." Seriously, I heard him describe it that way.

Finally, one without the dogs.

Tada!!!

All in all, a good night. 1 hour, 28 rivets set, 5 drilled out.

There are still a few more things I would like to do to the vertical, like drill out a couple of rivets and reset them, and clean up some of the skin edges, but for the most part, it can sit inside while I press on. I can’t believe it took me 16.5 hours for the vertical versus 44.5 for the horizontal. I think I would recommend to other newbies to start on the vertical. It seemed to be a lot easier, but I don’t know if that was because I had done everything once already on the horizontal, or because it really was easier. Whatever you do, don’t take my advice, though. You’ll die if you do.

Prev | Next

Leave a Comment » | Empennage | Tagged: , , , , , , , , , , , | Permalink
Posted by Andrew

VS Skin Riveting, Part Deux

February 12, 2010

Prev | Next

I’m writing this on Monday for Friday night’s work, so we’ll see how much I can remember.

After a couple minutes of clecoing on the right side of the VS skin, I got started riveting. First, I set every other rivet along the VS-702 front spar and the VS-707 middle rib.

Left skin on the bottom, right skin on the top. That crazy long cleco keeps sneaking into the pictures.

After rivting the front spar and ribs to the skin, here’s an interior picture.

Lower interior of the vertical stabilizer.

Here’s a picture of my “every-other-rivet” style. It works well.

Ready for the remaining rivets.

There are 39 rivets (not counting the tip and root ribs) for the front spar and middle ribs. After setting these 39, I’m ready to pull off the blue vinyl from the interior.

Starting to look pretty. So is your face.

Another rivet picture. (I’m not sure I got these in the correct order…Hmm.)

VS shop heads.

More rivets.

More shop heads.

<sigh>

<yawn>

Had enough yet?

Even more shop heads.

Alright, now I get to start removing the blue vinyl. This is where the gravy is. After all that prep work and riveting, you get to remove the vinyl to reveal a beautiful shine on the inside. I can’t wait to do this on the exterior skin (just before polishing). Flash on for visibility.

Starting to remove the blue vinyl.

I left the flash on for this one so you could see inside.

Inside the lower bay of the VS.

And the upper bay.

Upper bay of the VS.

After removing all of the vinyl, I moved on to riveting the tip (VS-706) and root ribs (VS-704 and VS-705) to the skin. All was going well, until I got the front of the root rib.

Anyway, for some reason the skin wasn’t sitting well on the rib. I later determined it wasn’t interference, just the natural curve of the rib.

The lower right side of the VS skin wasn't sitting very well on the root rib.

My solution? Use a tape-covered clamp to squeeze them together.

Alright, let's set this rivet.

That did the trick. Who’s next?

Looks perfect now.

Here I am riveting some of the rest of the root rib. I was very careful to not rivet the 6 holes on each side the instructions tell you to leave open for the empennage fairing. I probably won’t use all 6, but I can always squeeze these later, so why close any metaphorical doors?

In the middle of squeezing the root rib.

Here’s the VS (except the rear spar) all riveted together. Notice the 6 clecos in the holes to leave open.

Where's that rear spar?

I inserted the rear spar and started setting rivets. All was going perfectly, until I realized that most of the rivets couldn’t be set because of conflicting shop heads on the rear spar. I had tried two rivets that were close to having enough clearance, and I messed both of the shop heads up. Here’s one.

Bad rivet shop head there in the middle. Obviously.

And here’s the other.

Another bad shop head there on the left. See the cleco in the middle of the picture. The rivet that will go in that hole doesn't have a lot of room to be bucked.

I gave up on any other rivets that would be close with the squeezer. I’ve been doing so well recently with the gun and bucking bar, that I’ll just wait till I can make loud noises and set them with the gun.

Where I left off for today. I'll figure out how to set the remaining rear spar to skin rivets sometime next week.

One and a half hours today. 135 rivets set; some shot, some squeezed. Only a few will have to be drilled out later. Good night tonight. Hopefully next week, the dogs will get some directional stability.

Prev | Next

Leave a Comment » | Empennage | Tagged: , , , , , , , , , , , , , | Permalink
Posted by Andrew

VS Skin Riveting

February 10, 2010

Prev | Next

After 9 days of not working on the airplane, I finally made it out to the garage. In all fairness, though, I spent all last week working out hard, and preparing for a bachelor party at Snowshoe. West Virginia, right? Yup. It was actually pretty cool there. It was in the midst of the big blizzard that bent the east coast over last week, so Showshoe got somewhere around 20 inches of snow. Legend…wait for it…dary.

Anyway, I had previously drilled out the front spar(VS-702) to tip rib (VS-706) rivets, so here are the replacements. The one on the left doesn’t look all that good, but this is my third try, and I think I am going to leave good enough alone.

Front spar to tip rib rivets. Left one sucks, but I'm not going to make it any worse.

Then, I reset the VS-704 root rib to front spar rivets. I set the middle one fine, then messed up the outer two. Drill out, and reset them just fine on the second try.

Looking good from this side.

Here’s a shot of the shop heads for those three rivets.

Here are the shop heads for those three. Not too bad.

Next, the instructions tell you to cleco on the skin and start riveting. Here’s a shot of me getting ready to rivet.

Start from the middle of the front spar and work outboard, then back to the start and work inboard. Then, rivet along the middle rib aft.

Here’s a shot of some shop heads. You’ll have to click on the picture to see them.

Nice looking shop heads. You can also see my interior skin masking practice. Looks good, doesn't it?

More shop heads.

Another shot of the shop heads for VS-702 front spar and VS-707 middle rib.

And one more…

Once I get the other side of the skin riveted, I can take off the blue vinyl from the inside of the skins.

After riveting one side of the skin, I had to head inside to watch UNC play Dook. (Yes, that is how you spell Dook.)

Starting to look like something that could fly.

One hour today. I drilled out 3 rivets , set 5 rivets on the skeleton and 39 on the left VS skin. 44 total. Booyah.

Prev | Next

Leave a Comment » | Empennage | Tagged: , , , , , , , | Permalink
Posted by Andrew

VS Rear Spar Work

February 1, 2010

Prev | Next

After the big snow storm this weekend, work was delayed this morning until 10:30am. That gave me a few extra hours to recover from my ski trip yesterday. Maybe I’ll post a couple pictures later.

Also, I snuck in an hour on the vertical tail this morning after a quick workout.

First thing, I drilled out the 5 poorly set rivets from Saturday, and ended up shooting 67 rivets in today.

Here I am setting some universal rivets.

Me using the tape trick even on universal rivets.

Here are all of the lower vertical rear spar flush rivets.

Sorry for the weird angle. Here are the flush rivets on the forward side of the lower vertical rear spar.

About 4 of these didn’t sit completely flush after backriveting, so I’ll have to drill them out. I think it it because I am using some steel bar stock as a backriveting plate instead of a true backriveting plate. Also, my 12″ double offset backriveting set sucked. I think it is too long to really transfer the force. I swtiched to a shorter and it worked great.

One hour today. Set 67 rivets, drilled out 5 from the other day.

Prev | Next

Leave a Comment » | Empennage | Tagged: , , , | Permalink
Posted by Andrew

Skin Dimpling, Edge Finishing, Priming, Riveting

January 30, 2010

Prev | Next

I worked in sections today.

There was a big storm here last night, (and all of today), but I’ve learned that cleaning off the driveway is a lot easier if you do it when it is 3″ two times instead of once after 6″ has accumulated. Here’s what I woke up to this morning.

Snow!

Here’s after about an hour of shoveling. Good workout.

Coming down fast, but at least I cleared off the first 6".

Then, I got the c-frame out and finished the VS skin dimpling. I replaced the blue tape on the male die, and got almost no circles.

Simple but effective dimpling setup.

Then I countersunk all of the lower forward spar reinforcement holes from the plans. I haven’t used the countersink since I had to countersink HS-710 and HS-714 to accept a #30 dimple, so the countersink cage was already set up. All I had to do was verify in a piece of scrap. Yup. It’s perfect.

Beautiful countersinking.

Then, I cleaned and primed one interior side of the vertical skin, then the other. Here’s the first side drying.

Hurry up and wait to dry.

After finishing the second side and letting it dry, I pulled the forward section of vinyl off of the interior side of the skin. During assembly, no bucking bars will be needed in there, so there is no risk of scratching. Then I finished edge finishing the ribs, spars, and rear spar reinforcement, and primed each one. I didn’t prime them sitting perfectly horizontal, so I got some runs and some nastiness; some of them ended up getting touched up, and some got a second coat.  After they were all dry, I cleco those bad boys together in preparation for riveting.

Skeleton and rear spar taking shape.

I started with the skeleton, middle rib. Here’s my first VS rivet.

First VS rivet.

Then, I moved to the tip. See the upper rivet? The skins are sitting flush, this will have to be drilled out.

Ahhh! I suck at riveting.

And the lower rivet there started to bend over. I’ll have to drill out both rivets.

Two rivets to be drilled out.

Back to the middle rib, two more perfect rivets.

There are pretty good. I need to make sure that bottom one is driven enough.

See the fourth rivet from the right? Started to bend over, so I’m going to drill it out. Also, I’m going to put the shop heads on the thicker material here, also, they’ll be easier to inspect.

Uh oh. See the third rivet from the right? I was supposed to wait and rivet this with the skeleton. Slow down and follow the directions!

Two more rivets to be drilled out.

But I was feeling good about squeezing, so I kept going. Until these 4 rivets. Terrible…they all started to bend over. I think my rivet squeezer sucks. I have to squeeze really hard and it it tough to keep everything aligned. I think after I drill these out I am going to shoot and buck these.

4 bad rivets to be drilled out.

At this point, I had to walk away, I was tired, frustrated, and not making any progress. Ugh.

So far, 3.5 hours. I set some rivets today, but I’m not going to count any of them until I drill them out. I’ll update the rivet count later.

Prev | Next

Leave a Comment » | Empennage | Tagged: , , , , , , , , , , , , | Permalink
Posted by Andrew

Horizontal Stabilizer Complete

January 22, 2010

Prev | Next

Well, except for the fiberglass tips. And the elevator horn cutouts. But you get the idea.

I spent a half an hour in the garage early tonight finishing the last few things up. One of which was setting the last 4 rivets on the horizontal.

I had forgotten about the 4 rivets (4 on the left and right edges of the picture).

Also, I drilled out 12 skin rivets that were sitting a little proud, and reset them. Here’s the HS with the fiberglass tips just taped into place (to see what it looks like).

Finished HS with the tips taped into place. Looks good.

Short night, but the dogs flew in the newly designated “airplane parts storage” room.

Believe it or not, this is the best picture I could get out of about 10 tries. Jack and Ginger doing what they do best...looking cute.

Up next, the vertical stabilizer.

Prev | Next

3 Comments | Empennage | Tagged: , , , , | Permalink
Posted by Andrew

Started closing up HS

January 20, 2010

Prev | Next

I snuck out to the garage tonight for a couple minutes of getting the rear spar riveted into the HS. Before clecoing the rear spar in, I had a few rivets I needed to drill out from yesterday. First, this one, which was sitting a little high.

Down in front!

Easily drilled out and replaced. Then I moved on to two cases of split shop heads. Here’s the first one.

Split shop head #1.

And the second one. I think this happens when I start to set the rivet a little crooked and then try to straighten out.

Split shop head #2. Uglier.

Anyway, I fixed both of those, and took this picture of the new shop head as representative of all three.

It's art to me.

Then, I clecoed the rear spar into the HS and started dropping rivets in. These haven’t been squeezed yet, but I thought it looked cool.

Ready to start squeezing the skin to spar rivets.

Then Ginger came out to ask why I wasn’t inside rubbing her belly.

"What are you doing out here, dad?"

She wouldn’t come on this side of the workbench, but was definitely curious. She was staring at me from under the workbench for about 20 seconds before I realized she was down there.

"Dad, come inside and let me lay on you."

After squeezing all of the skin-to-spar rivets, I needed to find the BSPQ-5-4 blind rivets. Here they are.

BSPQ-5-4.

Here are the HS-708 (rib) to rear spar holes they fill.

Last 2 (4, 2 on each side) holes in the horizontal stabilizer.

Done.

I don't love having these blind rivets showing, but no one will see them when the elevator is installed.

Here’s a picture of the almost final project. I circled about 7 rivets on the bottom side (the HS is upside down here) that I want to replace.  I’ll fix those this weekend, and inspect the top side before calling the HS complete.

Almost done. Looking good.

I ended up spending almost 2 hours outside. Drilled 3 rivets out, set 178.

Prev | Next

1 Comment | Empennage | Tagged: , , , , , , , , | Permalink
Posted by Andrew

More Right HS Riveting

January 17, 2010

Prev | Next

After a nice day off (had to work), I got back in the garage this morning for some good progress.

I started off by assessing the damage from the other day’s skin denting fiasco. I contemplated removing HS-707 entirely (from the top skin, too) so I could really get in there and smooth this sucker out. I even got everything mocked up in the c-frame again to look at the feasibility of getting rid of this dent. Then I decided I would have probably caused more harm than good, and that it looked a lot better today than it did the other day. After re-clecoing HS-708 into the skin with HS-707 and re-riveting the bottom skin to HS-707, I took this picture. The dented area is between the bottom two rivets in the picture. It’s really not that bad.

The denting between the bottom two rivets is really not that bad. And, it's on the bottom of the right HS. No one will look there. Unless you are reading this, and come to see my airplane, and want to see the dent on the bottom of the right HS. Damn you.

Anyway, with that done and behind me, I clecoed in the front spar assembly from Friday.

Upside-down HS assembly after starting to cleco the front spar (already riveted to the left HS skin) into the right HS skin.

CRAP! I forgot to remove the blue vinyl from the inboard bay before clecoing everything together. Okay, let’s un-cleco, remove, the vinyl, and recleco. Great. After inspecting (admiring, really) the assembly, I noticed a loose rivet (as opposed to a prude rivet. Hehe.). It was one of the two forward HS-707 rivets (by the denting). Grrr. Okay, should I un-cleco everything, and risk scratching everything in the process, or drill out two small rivets in the HS-404 to get my arm in there. I decided to go with drilling, since apparently I am really good at drilling rivets out. Without any issue, I got HS-404 removed and reached in to replace the offending rivet (second from the right in the picture).

HS-404 removed so I could reach in to replace the loose rivet.

Then, I reinstalled HS-404. (But took this picture before I actually riveted it to HS-702 (front spar) and HS-405 (aft root rib) behind the spar. Just pretend there are perfectly driven rivets there.

HS-404 reinstalled and the rest of the skin clecoed together.

Time to skin rivet. I like this part. Here is my technique. I stick the appropriate sized rivet in the hole, cover with blue tape, then reach in with the bucking bar, and shoot with my flush set, which is also covered in blue tape. Then, I remove the rest of the clecos, put rivets in again, and move all this little pieces of blue tape over one. (Then I figured out that on the second round, I could remove all the blue pieces of tape and run a whole line of tape along the line. I just had to make sure verify which rivets I had the bucking bar behind by pushing up on it a little. you can then see the rivet pushing up behind the tape. Bucking bar in place, I can set the gun down on the rivet and shoot.)

If you were counting, you noticed there are now two pieces of blue tape between the flush set and the rivet (and my fragile HS skin). This worked well for me, prevented further damage, and gave me some friction to help keep the set in place.

Rivets ready to set, covered with blue tape.

So, I knocked out all of the rivets needing to be bucked (I think it was 42 per side) before inspecting all my work for any issues. I think I found 5 skin rivets I wanted to replace. Here is a good example. The shop heads of all of these look great, but I want those rivets perfectly flush. I didn’t take an after picture (sorry), but I assure you, the one on the right now looks like the one on the left.

Bad rivet on the right. Replace.

After bucking all of those, I moved the now very big HS assembly to the floor while I cleaned off my workbench. Nice and clean again.

Clean workbench!

Then, I brought the HS back up on the table to squeeze the rivets that could be squeezed on the HS-601PP (skin) to HS-404 (inboard tip rib), HS-405 (inboard aft rib), and HS-706 (tip rib). The instructions have you leave 5 holes open on the inboard lines for the empennage fairing attach holes on the top only, but I decided to leave the same holes empty on the bottom for now, just to have clecos there on both sides to hold the HS off the table.  I also left some clecos in both sides of the tip ribs (although I left less on the right than I had on the left the other day, so I squeezed a few more on the left. ) Anyway, the HS is upside-down here. Left side is in the foreground.

Oooh, pretty.

Another shot. Still need to get that rear spar done. Look in upper right side of the picture. The dented area (I really shouldn’t call it dented anymore) is in the middle of the leading edge there. (I know the picture is from a distance, but the point is it’s not that noticeable.)

More pretty!

And after I flipped the HS right side up.

Shiny and clean.

After a hard day’s work, I stood back and admired the almost finished product.

I need a bigger workbench.

Good 3.5 hour day today. 146 rivets set, 14 drilled out.

Next up:

1) Remove rest of blue vinyl from inside of HS.
2) Rear spar work.
3) Finish riveting holes in HS.
4) Figure out what is going to “fly” when I finish the HS.
5) Hang HS for storage

I also decided that I am going to keep a separate page for tips. I keep learning these little tricks along the way. I should write them down.

Prev | Next

1 Comment | Empennage | Tagged: , , , , , , , , , , , , , | Permalink
Posted by Andrew

« Previous Entries
Next Entries »